|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Product was very good. Received quickly and complete
 ;
Although printing quality is not the best, the manual was very helpful in order to reactivate this ancient but still good electronic musical instrument.
;
as a first-time user and buyer from this site, i found the overall service outstanding!! this product is a godsend as, without it, i would never have been able to find my way around and use my machine as intended. i will certainly use this site again as required. many many thanx!!
;
This manual is exactly what I needed. This site always has every manual I need, and it is also much less expensive then most other sites. This is the only manual site I will use.
;
Useful manual, good scan, worth the pay if you find the unit difficult to operate.
HK3250 engelsk
11/01/98 14:28
Side 4
Front Panel Controls
1. POWER BUTTON
Press this button to turn the power on. Press again to turn the power off. If you connect the other components to the switched outlet, it can also be used as a system power button.
5. BALANCE CONTROL
This control is used for balancing the relative sound volume of the left and right channel speakers. Clockwise rotation reduces the volume from the left speaker, counterclockwise rotation reduces the volume from the right speaker.
8. TAPE MONITOR BUTTON
Press this button to select input from a tape deck.
9. TUNE / PRESET BUTTON
When AUTO is not lit, the TUNE/PRESET buttons will allow you to tune to a station manually.
2. HEADPHONE JACK
Stereo headphones can be plugged into this jack for private listening. Headphone impedance should be between 8 and 2K ohms. Best results between 200 and 400 ohms.
again to store preset station. NOTE: When you store a frequency in a memory location that already contains a frequency, you replace the previous frequency. If your receiver is disconnected from AC power for more than about 2 weeks, it loses all stored frequencies.
ENGLISH
6. 1 / 2 SPEAKER SWITCHES
These switches allow you to select various combinations of speakers as follows; s To drive 1 pair of speakers, push only the speaker 1 switch in. s To drive a second pair of speakers, push only the speaker 2 switch in. s To drive both pairs of speakers, push both 1 and 2 switches in. s To use headphones for private listening or monitoring, leave both 1 and 2 switches pushed out
10. TUNE / PRESET SCAN BUTTONS
Press the TUNE/PRESET button to light up PRESET then use the up/down buttons momentarily to scan the preset station frequencies. The receiver stops at each preset location from 1-30 that has been entered in memory. Hold the button down to skip through the presets quickly. In the TUNE mode press these buttons to change selected frequencies.
12. SEEK STEREO BUTTON
Press this button, �Auto� will illuminate in the display. Then press the TUNE/PRESET button. The tuner will automatically seek out stations in your area that have enough signal strength to be listenable. The tuner will stop on stations until the SEEK/STEREO button is pressed again.
3. BASS CONTROL
Modifies the low-frequency sound of the left and right channels as much as +/- 10dB. Set this control at a suitable position for your taste and room acoustics.
13. VOLUME CONTROL
Turn the VOLUME clockwise to increase the volume and counterclockwise to decrease it.
4. TREBLE CONTROL
Modifies the high-frequency sound of the left and right channels as much as +/- 10dB. Set this control at a suitable position for your taste and room acoustics.
11. STATION MEMORY BUTTON
Use this button to store an AM or FM frequency. Press this button and select one of 30 preset locations to store the frequency with the TUNE/PRESET buttons while the MEM indicator blinks, press MEMORY
14. DISPLAY WINDOW
This window shows the state of operation for easier control of the receiver. It also contains the IR Remote Sensor.
7. INPUT FUNCTION SELECTOR BUTTONS
Press these buttons to select the desired input source.
4
|
|
|
> |
|
